DM002 drone review: Dirty cheap and easy to build

DM002 DIY drone review

Recently, I received the DM002 quadcopter for tests, a Chinese RC toy quite entertaining at an attractive price. I assembled it and played around with it, and now it is time to write my review, of course at the end of which I will draw the conclusions.

As I previously mentioned many times, the fact that a drone comes in parts should not scare you. In my opinion, the fact that you can build your quadcopter doubles the fun.

The DM002 is available in two variants. One with a 5.8G camera and one with a WiFi FPV camera. Both black and white versions can be found.

dm002 quadcopter review - Closer lookDM002 micro FPV quad highlights

  • Easy to build DIY KIT;
  • 600 TVL camera with angle adjustment;
  • Real-time image transmission;
  • 5.8G, 40CH VTX with adjustable output power;
  • One key return to home (not tested);
  • Multiple speed rates;
  • Low voltage protection;
  • LED lights for night flight.

DM002 quadcopter review with build instruction

The DM002 micro FPV quad was sent to me by Banggood to make an honest review. BG is a very popular online store among RC enthusiasts. They commercialize not just quadcopters but as well as multi-rotor parts.

Arrived home, I immediately opened the package in order to check its contents. I was curious if it includes everything required to build a flying machine.dm002 quadcopter review - Parts list

DM002 DIY quadcopter KIT parts list

  • 2.4G transmitter;
  • 95mm frame kit;
  • 2in1 flight controller with receiver board;
  • 600TVL camera with 25mW/80mW/200mW 5.8G 40CH VTX;
  • Camera holder;
  • Camera protective case
  • 3.7V 300mah Li-Po battery;
  • USB charging cable;
  • Four pieces of coreless motors (2xCW and 2xCCW);
  • Two sets of two-leaf propellers;
  • Propeller removing wrench.

It also included a small instruction guide about how to assembly the DM002. The step-by-step guide refers to all DM002 variants.

Curiously, the included user manual is for a completely different RTF drone. Later, I found out that it was for the DM003.

DM002 quadcopter review – Transmitter

The transmitter is very bulky and toyish, which is unsurprising for such a cheap RC toy. No status LCD on the front panel, just four trimming buttons.dm002 quadcopter review - Transmitter

The left shoulder button allows switching between flight speed rates (Low, Medium, and High). The right shoulder button should enable the flip mode, but till now, I haven’t managed to do any flips.

In case the DM002 starts to fly abnormally, I recommend first to try to re-calibrate the gyro by pushing both sticks to the lowest left position.

DM002 quadcopter review – Camera

The included VTX camera is very similar to the Eachine MC01 camera.

According to the advertised specs, you can switch the TX power between 25mW, 80mW, and 200mW, but no instructions about how to do this.

The nickel-plated 3-leaf antenna is directly soldered to the VTX board.

Thanks to the included protective case you can adjust the camera’s angle from straight ahead to straight up.dm002 quadcopter review - Camera

On top of the camera is a setting button that allows the TX frequency (Band/CH) to be changed. Featuring a total of 40 channels (including race band) the camera is compatible with almost any 5.8G FPV display.

On the rear part of the DM002 camera is a blue 7-segment display that shows the actual CH#, Band, and TX power.

The camera offers pretty good quality and the range is just perfect for proximity park flying.

DM002 quadcopter review – Build instructions

First, you don’t need any special tools or soldering iron to assemble this DIY drone.

The mainboard comes with four motor connectors and two power cables. One cable serves to power up the DM002 quadcopter, and the other one feeds the FPV camera.dm002 review - main board

Two motor connectors are white, and the other two are red, which is nice because this way you can’t reverse CW with CCW motors.

Both frame arms and propellers are marked with “A” and “B” respectively.

According to the instruction guide, the first step is to mount the propellers on the motors. Props “A1” and “A2” go on motors with red&blue wires, respectively “B1” and “B2” on motors with white and black wires. Note: there is no difference between A1 and A2 or between B1 and B2.

The second step is to mount the motors on the motor holders.dm002 review - Building step 3dm002 review - Assembling step3

The third step is to mount the flight controller. It is positioned (orientated) on the frame as the power cable matches the cut on the frame.

Step four is to mount the camera holder and install the camera. When you put it on its place, you can interconnect the camera with the mainboard.

The final step is to plug the motors into the mainboard. That’s it! You are done with building your first quadcopter :)

DM002 quadcopter review – Test / First Usage

Powering up the DM002 for the first time, I found out that near each motor connector, there is an SMD LED—blue ones in front and red ones in the rear.

Binding the DM002 with the remote controller can be done by pushing up and down the throttle stick (left one in mode 2).

Nasty surprise: by gently pushing the throttle stick up, instead of rising, the quad started to rotate around its axis.

I powered it off and checked the propeller and motor order, everything seemed to be okay. The second try was the same :( Then I got the idea to check the direction of rotation of the motors with my fingers. One of the motors turned in the wrong direction. I plugged it reversely, and after that, everything seemed to be fine :).

Although it doesn’t have versatile flight modes like the Eachine QX95, I liked that the DM002 is quieter and also more stable.

My first flight ended after about 4 minutes. I believe flight autonomy can be extended to 5-6 minutes by removing the camera.

Pricing and availability

If you want to build your first FPV quadcopter, this nice DIY KIT can be found for $39.99 with free shipping here. If you are scared about the building process, you can opt for the DM003, which has basically the same flight performance for much less money.dm002 review - Final words

REVIEW OVERVIEW
Price-performance ratio
Easy to assembly
Camera / FPV
Transmitter
Flight performance
dm002-quadcopter-reviewAlthough the DM002 is not a well documented DIY drone KIT I managed to assemble it in 20 minutes. The package includes all the required parts. There are no tools required. In my opinion this quad is an excellent RC toy for first-time pilots interested not just to fly but also to learn how these things work. <br> The good<br> +Easy to assembly DIY kit;<br> +Suitable for first-time pilots;<br> +Very silent;<br> +5.8G FPV camera.<br> <br> The bad<br> -Proprietary flight controller without Acro flight mode.<br> -Poorly documented;<br> -Lack of spare parts.<br>

11 COMMENTS

  1. Friends, received this drone, I have some problem with it. It rotates permanently. Can someone send me the calibration information
    Thanks,
    Makarest

  2. Hi, could you tell me how you did the fix for the motor that turned the wrong way?

    Cos the connects only fit one way.

    Thank you.

    • You have two options:
      1. remove the plastic frame of the motor plug, this way you can plug the motors in both ways
      2. un-solder the motor connector and solder it back in the right order

LEAVE A REPLY

Please enter your comment!
Please enter your name here