Home Drone brands Eachine drones Eachine Racer 250 PRO review: Nothing like the first edition

Eachine Racer 250 PRO review: Nothing like the first edition

Lots of features and madness amount of power for a fair price

Brushless quadcopters aren’t cheap, but the Eachine Racer 250 PRO comes at a surprisingly reasonable price of $129.99, considering its nice design and impressive features. Of course, like many budget FPV drones, there are Pros and Cons to the Racer 250 Pro which I’m planning to reveal during my review.

The Eachine Racer 250 PRO drone was announced in two variants, PNP and RTF. In comparison, the PNP package contains only the aircraft (fully equipped with FC, ESC, motors, camera, and VTX), the RTF (Ready to Fly) package also includes an RX module, transmitter, flight battery, and charger.

Eachine Racer 250 Pro review - Introduction

Over time, Eachine developed into one of the most active players in the drone market. They announce new models almost every week. They mostly became popular for the excellent price tag and spare parts availability. Eachine is constantly striving to improve their products. The “Pro” edition of the Racer 250 is upgraded in every term compared to its predecessor.

Eachine Racer 250 PRO highlights

  • Versatile F3 6DOF flight controller;
  • Blheli_S 20A ESCs (supports Dshot 300 and Dshot 600);
  • Powerful 2205 2300KV brushless motors;
  • Compatible with up to 5-inch propellers (comes with 3-blade ones);
  • 5.8G 600mw 32ch VTX with built-in OSD (battery voltage and flight time).
  • 1000TVL CCD camera, NTSC / PAL switchable, suitable for night flights.
  • Powerful head-lights (two pieces of 3W LEDs);
  • Multi-color tail light.

Eachine Racer 250 Pro in-depth review

Before I get into details, I should thank Banggood for the continuous support of my website with new and exciting products.

Damn, DHL, they did it again. The package traveled from China to my country in 3 days, and the last 100 km took another six days.

Because I recently received two FrSky receivers and the Taranis Q X7 transmitter, I opted for the PNP (Plug-N-Play) package. If you already own a transmitter is not just “green” to order PNP package but also cheaper (less shipping cost and custom fees) than the RTF package.

Eachine Racer 250 PRO review – Design and build quality

Compared to its predecessor, the non “Pro” aka Floureon Racer 250, it has a better build quality. Unfortunately, the designer kept the bottom plate as a power distribution board which could be a pain in the ass if it needs to be replaced.

As you can see in the image below, there are few visible differences between the two versions of the Eachine Racer 250. In the case of the Racer 250 Pro, the tail light is shorter (it has only 3 RGB LEDs), the FPV antenna is moved from center to rear, and it uses 3-blade propellers instead of 2-blade ones.

Both motors and ESCs are upgraded compared to the previous model. While first edition (non-Pro) was designed for 3S batteries, the “PRO” edition is optimized for 4S Li-Po. Theoretically, higher voltage means more punch.

On the left side, there are two microswitches. While the frontal one allows to turn ON/OFF the headlights (2 x 3W), the real one allows to turn ON/OFF the taillights. 3 additional DIP switches allow setting the color of the tail light (Green, Red, Blue, Orange, Green Purple, or White).

In front, there is a camera mount with vibration reduction damping balls, which allows for installing an additional DVR camera (like GoPro Session or RunCam 3) in order to record the journey of your flight.

The flight battery can be attached to the top plate using the included Velcro band.

By default, the F3 6Dot flight controller comes with CleanFlight firmware, but you can flash it with BetaFlight as well.

Eachine Racer 250 PRO review – Camera, VTX, and OSD

As I previously mentioned, the 1000TVL camera is attached to the frame using a nylon camera mount, which allows slight adjustment of the camera’s angle (~25 degrees).

The camera has good low-light capabilities so pilots can enjoy their uninterrupted flights day and night.

The real-time image transmission is achieved using a 5.8G, 32CH, 600mW VTX module with built-in OSD. The high broadcast power is not necessarily a good choice because it is illegal to transmit over 250mW in most countries.

The OSD is very handy and allows you to monitor the battery voltage and the elapsed flight time permanently. The “OSD bar” is located on top of the screen without disturbing your field of view.

Eachine Racer 250 PRO review – Initial setup

In the case of the RTF package, you need just to attach the propellers and you are ready for the first flight. In the case of the PNP package, you need to solder the RX module to the FC, to configure & bind the transmitter, and set the AUX channels (Motor ARM/Disarm and Flight mode switch).

No direction marks on the propellers. While 5048R props are installed on motors with blue nuts, the 5048L props are installed on motors with black nuts.

VTX is set to CH1 (5867MHz) by default. If you need a different channel, you can change it by pressing the red push button on the VTX.

Note: Before powering ON, you need to attach the FPV antenna to the VTX module, otherwise, it can burn out and no more FPV.

Eachine Racer 250 PRO review – Test flight / Flight performance

First, no motor Lock/Unlock sequence as described in the user manual. When you push up a bit the throttle stick, the props start to spin. Warning: the propellers are very sharp and they can cause serious injuries.

After a few minutes of flight, I noticed that the Racer 250Pro is not a toy for kids, it is a powerful flying machine. Frankly, to explore its full potential, you need serious flying skills. It is damn fast and agile.

The built-in buzzer will warn you when the battery is nearly empty, and it’s time to land. This feature is very helpful in the case of LoS (Line of Sight) flights. Frontal LEDs are also very helpful because they allow you to determine the drone’s orientation even in strong daylight.

Using a 4S 1300mAh Li-Po battery, I got an average flight time of 6 minutes.

Pricing and availability

This nice FPV quad is $ 129.99 in the PNP package here. If you don’t own a suitable radio system (RX & TX) and a flight battery, I recommend that you look for the RTF package.

REVIEW OVERVIEW
Price–performance ratio
Design and Build quality
Camera & FPV & OSD
Flight performance
Flight time
I joined to the FirstQuadcopter team last year. I love diving into the latest and greatest in drone technologies and seeing what they can do. Content moderator and helpdesk.
eachine-racer-250-pro-reviewCompared to micro brushed quads, the Eachine Racer 250 PRO has insane amount of power. It feels like it came out from the Fast and Furious movie :D. You would think that due to its low price is designed for fist-time pilots but, in my opinion, even Pro pilots would be satisfied with the abilities of this FPV drone. <br> What I liked most<br> +Excellent price tag;<br> +Very robust construction. Takes well crashes;<br> +Bright LED lights;<br> +Built-in buzzer, real help if you need to find the aircraft after a crash;<br> +FPV with sound (VTX with built-in microphone);<br> +Impressive flight performance;<br> +Good image quality with OSD.<br> <br> What I didn't like<br> -Not adjustable VTX. 600mW broadcast power (probably illegal in most of the countries);<br> -It can be found in combo only with FlySky radio;<br> -The bottom plate is used as a power distribution board.<br>

2 COMMENTS

LEAVE A REPLY

Please enter your comment!
Please enter your name here


Exit mobile version