iFlight BOB57 6 Inch Cinematic LR Long Range

iFlight BOB57

iFlight’s new BOB57 6″ FPV drone was specially designed for long-range flights. It comes with GPS positioning and an optional ELRS or TBS Crossfire radio receiver. The 6-inch frame has an H-shape design and 6mm thick arms.

In addition to the onboard FPV camera, can be equipped with GoPro 10 for cinematic 4K recording. According to the advertised specs, with a 6S/4000mAh battery, you can have more than 9 minutes of flight time.

Key features

  • 6-inch drone re-engineered: This drone was specifically designed for 6 inches;
  • H-shaped frame: Robust middle section for less props in view while remaining stiffness;
  • XT60 front mount: Compare to other drones the mount sits in the front and gives;
  • Built-in BEC to directly power for GoPro (no battery needed);
  • Hy motor design: This motor is optimized for 6 inches. Can be used with bi- blades (efficiency) and tri-blades (agility & trust);
  • Antenna mount: Solid antenna mount for fewer oscillations when using long antennas
  • Long backbone: Enough space for up to 3000mAh 6S batteries
  • Gladiator shell: Protection shell from dust and water droplets (shall be removed for maximum flight time)
  • GPS: A high-end GPS is used to minimize the risk of failure during proximity flights
  • ESC: The drone consists iFlight’s new ESCs with a built-in spike absorber for more reliability;
  • Radio receiver: Optional ELRS or TBS Crossfire Nano RX;
  • Action camera mount: Can carry a full-size GoPro;
  • Long flight time: 9+ testing with 3000mAh 6S Lipo or 4000mAh 6S Li-Ion

Technical specifications

6″ Frame kit Upper(middle) plate thickness: 2.5mm
Bottom plate thickness: 1.5mm
Total Dimensions: 254*254mm
Bottom to top distance: 22mm
Geometry: H-shaped frame
Top plate thickness: 2mm
Arm Thickness: 6mm
BLITZ F7 flight controller MCU: STM32 F722
Gyro: BMI270
Barometer: DPS310
OSD Chip: AT7456E
Flash: 32MB (Blackbox flash)
UARTS: 6
Motor outputs: 4x (SH1.0 connector)
I2C serial: SDA / SLA pads
SmartAudio / IRC Tramp VTX protocol supported
LED controller: Yes
Beeper pad: Yes
Firmware target: IFRC-IFLIGHT_BLITZ_F722
Mount pattern: 30.5*30.5mm / 4mm PCB hole diameter
Dimensions: 36.5*35 mm
Weight: 7.8g
BLITZ E55 55A 4IN1 ESC Model: BLITZ E55
Item Name: BLITZ E55 55A ESC
Mounting Holes: 30.5*30.5mm/Φ4mm
Weight: 15.3g
Supports 2-6S lipo input
MCU:G071
Constant: 55 Amps
Burst: 65 Amps
Current sensor: Yes
BEC: No
Current rate: 200
Supports: DShot DShot150/300/600/MultiShot/ OneShot etc.
Target: IFLIGHT_BLITZ_G2
Ellisvanjason 2506 motors 2506.5 1500KV 6S
Gemfan 6032 3-Blade propellers 2 CW + 2 CCW ( In Green)
2 CW + 2 CCW ( In Black)
I started to write and share tips on FirstQuadcopter.com about two years ago. I'm a racing drone addicted, but I treat myself :D

1 COMMENT

LEAVE A REPLY

Please enter your comment!
Please enter your name here