Drone accessories reviews & ratings

The latest drone accessories reviews at First Quadcopter. Drone accessories reviews, ratings, buying advice, and price comparison.

We review all kinds of accessories, from Gimbals, Backpacks, FPV cameras, FPV monitors, and Drone Goggles to Radio Transmitters and Receivers. Find the best accessories for your drone.

Best drone accessories reviews

LN Motor FS3115 900KV: Cinelifter Motors for 9-10″ FPV drones

LN-Motor FS3115 900KV
The FS3115 900KV brushless motors from LN-Motor are intended for 9 and 10 inch cine-lifter FPV drones. These motors can be used in X4 and X8 configurations, depending on how much payload you expect to install on your drone. Each motor can generate a...

I’ve been testing the Jumper T14 for 2 weeks – here’s the pros and cons

Jumper T14
The Jumper T14 is the company's third radio controller reviewed here on FirstQuadcotper. The T14 is a mid-level transmitter with a built-in 1W ERLS module. It adopts RadioMaster Boxer and TBS Mambo-like form, factor, and layout. Not everything about the T14 is whoa-inducing; it...

SUNLU 3D Printer Enclosure: An absolutely essential accessory!

Sunlu 3D Enclosure
3D printers are like dust magnets; if you don't cover them with something in a few days, they will be covered by a fine layer of particles. Moving parts are greased with vaseline, from which the dirt is difficult to remove. The SUNLU 3D...

RushFPV BLADE F7 AIO: FC for Hassle-free FPV drone building

RushFPV BLADE F7 AIO
RushFPV is known for its easy-to-use, solder-free flight controllers. This review will examine their latest BLADE F7 45A AIO flight module with a built-in 45A ESC. An AIO (All-In-One) flight controller is a type of flight control system used primarily in compact FPV drones. AIOs...

RadioMaster Bandit ExpressLRS: 915MHz ELRS RX and TX

RadioMaster Bandit series (TX and RX)
After testing so much 2.4GHZ ELRS hardware, I thought it was time to review some 915MHz equipment too. RadioMaster's Bandit series includes three TX units (RF, Micro, and NANO) and two RX modules (BR1 and BR3). In this article, we will check out the...

Zhiyun FIVERAY M20C: Light Up The Sky!

Zhiyun Fiveray M20C
Drone light painting empowers photographers to craft avant-garde content using photographer-controlled light from the sky. The Zhiyun FIVERAY M20C is sufficiently small and lightweight to be installed on most consumer drones, allowing the creation of viral social media content. With more than 16 light...

Fullsend 6S 6000mAh Li-Ion: Holy Grail of long range FPV

FullSend LR 6S 6000mAh Li-ION battery
Lithium-ion or Li-ion batteries generally have a higher energy density than other battery chemistries, including LiPo. This means that Li-ion packs can store more energy in the same physical size, allowing longer flight times and increased range. For example, by comparison, the iFlight Fullsend...

ISDT 608PD charger: Tiny but Mighty

ISDT 608PD
When I started this hobby, I remember that LIPO chargers were big, heavy, and had a max power of 30-50W. Instead, the ISDT 608PD fits inside your pocket, weighs just 85 grams, and has a charging power of up to 240W. Furthermore, it can...

Jumper T20 GEMINI: Fully-Featured ELRS radio!

Jumper T20 GEMINI
The Jumper T20 GEMINI is the third model of the family, and as its name suggests comes with a built-in twin ELRS TX module. The T20G inherits the small form factor and full-size RDC90 gimbals of the T20S. In this review, we will discover...

HQProp propellers for all-sized FPV drones

HQProp propellers
Since I started building FPV drones, HQProp has been in the top three of my personal choice. I tried to avoid using propellers from known brands despite being cheaper. This review will look closer at six of their props. Propellers, also known as props, are...

ChiTu Conjure PLA+ and High Speed PLA 3D filaments

ChiTu Conjure JAMG HE filaments
Probably everyone into 3D printing hobby has already heard about the Chitubox slicing program. Still, in this review, we will focus on the company's ChiTu JAMG HE Conjure PLA+ and Hi-Speed PLA Pus 3D filaments, which I had not heard until a few weeks...

MEPS SZ F7 HD: Easy to wire high-performance flight controller

MEPS SZ F7 HD
Here at FirstQuadcopter, we start 2024 with a flight controller review. The MEPS SZ F7 HD is the company's second FC we tested. Both have similar features, mainly just the mounting pattern difference. The smaller 20x20mm is suitable for compact 3-5" CineWhoop drones, and...

Master Airscrew 9″ propellers for Long-Range FPV drones

Master Airscrew 9-inch propellers
Last week, I built a long-range FPV drone using the Chimera 9 ECO frame, and while researching the required components, I came across Master Airscrew, a US brand with a tradition in propeller manufacturing. So far, I have only used HQprop, Dalrop, and Gemfan...

MEPS SZ2207: Are these FPV motors better than company’s reputation?

MEPS Space SZ2207 motor
The SZ2207 will be the second FPV motor from MEPS reviewed here on FirstQuadcopter. Both motors are intended for 5-6" racing drones. While the SZ2306's stator has 23mm width and 6mm height, the SZ2207's stator is 22 mm/7 mm. The 2207 has a narrower...

iFlight BLITZ F7 V1.1 flight controller: Is it good?

iFlight BLITZ F7 V1.1
The flight controller (FC) is the brain of the FPV drone and is probably the most critical component, as it is responsible for stabilizing the drone. The FC generates the motors' control signals based on the pilot's and sensors' inputs. If you are starting...

LN-motor FS2812 and FS2306 brushless motors for FPV drones

LM-Motor FS2306 and FS2812
Commonly, the product name of FPV motors is formed by a group of two numbers. The first one refers to the dimensions of the motor and the second one to the speed of the motor. Brushless motors have two main parts: the rotor with...

Ricoh Theta X: The Ultimate 5.7K@360° stabilized camera

RICOH THETA X
Ricoh is more known for its printers and copiers than for drone cameras. The Ricoh Theta X is the company's latest 360-degree camera and a direct competitor of the Insta360 X3. Both are great cameras for capturing 360° photos and stabilized videos. The Ricoh Theta...

SUNLU AntiString PLA filament for high quality 3D prints

SUNLU APLA
Stringing is a common 3D printing problem that can be annoying when you want quality results without post-finishing. To solve the root of the problem, SUNLU came on the market with the first AntiString PLA filament, an upgraded version of the regular PLA filament. Stringing...

BetaFPV SuperG Nano TX: First GEMINI ELRS transmitter

BetaFPV SuperG Nano TX
Since I built my first ExpressLRS-enabled FPV drone, I converted all existing drones to ELRS due to the excellent range and link stability. BetaFPV's new SuperG Nano TX module is the first GEMINI-compliant transmitter with dual-frequency diversity communication. The module was developed by BetaFPV...

ELEGOO Neptune 4 Max: Speedy XXL 3D printer

Elegoo Neptune 4 Max 3D printer
The ELEGOO Neptune 4 Max is the largest 3D printer that I reviewed. With a massive 420*420*480mm build volume, you can print big models at once without the need to glue multiple parts together. The Klipper firmware will also be a first for me....

Skystars Bolt5 (Foxeer Caesar) racing drone frame

SkyStars Bolt5 \ foxeer caesar
Racing frames like the Skystars Bolt5 or Foxeer Caesar prioritize light weight and aerodynamic efficiency for maximum speed and maneuverability. Their geometry is optimized to have the smallest friction in the air, and the battery is mounted underneath the frame to obtain the optimal...

JHEMCU GF30F722-ICM: Most affordable F7 flight controller

JHEMCU GF30F722 flight controller
A few months ago, I built an iFlight Nazgul5 V3 FPV drone, and being on a tight budget, I looked for a cheap but versatile flight controller (FC). While most F7 flight controllers from reputable brands such as Diatone, SpeedyBee, RushFPV, HGLRC, or iFlight...

SUNLU PLA and PLA+ 3D filaments: Is it Worth it?

SUNLU PLA+ and PLA review
When I show my 3D-printed objects to friends, the most common question is, "How much does the filament cost?" SUNLU is known for its affordable 3D printing materials. In this review, we tested their PLA and PLA+ filaments. To check the quality and usability,...

DJI O3 Air Unit Waterproof case from DarwinFPV

DarwinFPV DJI O3 Air Unit waterproof case
The DJI O3 Air Unit is probably the most expensive component of any FPV drone, and you will probably want to protect it from crashes and harsh weather conditions (rain and snow). DarwinFPV's CNC aluminum case provides IP68-level waterproof, dustproof, and impact resistance. Additionally,...

VIFLY WhoopStor 3: 1S Charger for Whoopsters

ViFly WhoopStor 3 charger
Micro CineWhoop style FPV drones drain the battery very fast and have only 2-4 minutes of flight time. This means that you will need about 20 batteries for one hour of fun. The VIFLY WhoopStor 3 allows you to charge up to six batteries...

Walksnail Avatar HD Nano V3: Digital FPV for all your drones

Last month, Caddx introduced its fifth digital FPV kit, the Walksnail Avatar HD Nano V3. Although its name is suggested to be super small, it is one of their most sophisticated video transmission systems suitable for small CineWhoop drones and bigger racing/freestyling FPV quadcopters....

POPDEER S500: A little power horse

POPDEER S500 power station
The Popdeer S500 offers a storage capacity of 518 Wh and 500W of output power. It is the smallest solar generator in size with these power parameters that I have tested so far. It is almost twice as small as the 300W power station...

SKYRC B6neo Smart Charger: Tiny & Powerful

SkyRC B6neo
All-new from SkyRC is the B6neo 200W pocket smart charger. It has the size of a matchbox and packs many features, including a 1-inch display, dual-power input, up to 10A charging current, and 6S LiPo compatibility. Furthermore, it doubles as a customizable power supply...

SUNLU S2 Filament Dryer: Moistureless 360° Surround Heating

SUNLU S2 FilaDryer
Many 3D printing filaments are hygroscopic, which means they readily absorb moisture from the environment when they are removed from the original package. Moisture can turn into steam in the hot end, leading to issues like poor layer adhesion, bubbling, or even clogging of...

VEVOR Portable Power Station: Very budget friendly solar generator

Vevor 296Wh|300W Power Station
Power stations have improved drastically in recent years and have become more and more used for outdoor activities as they are much more portable than gas generators. In this review, we will have a closer look at the Vevor 300W mini solar generator that...

Ultra Durable water-proof ELRS receiver from DarwinFPV

DarwinFPV waterproof ELRS receiver
Regarding FPV drone parts that are waterproof or water-resistant, it's important to note that, while some components like this DarwinFPV Cement ELRS receiver might have a certain level of protection against moisture, truly waterproof FPV components are relatively rare due to the nature of...

Mintion Beagle V2: Swiss army knife of 3D printer monitoring

Mintion Beagle V2 camera
Even though I'm a MacGyver-type guy, I learned the importance of selecting the right tools for the job. Improvising will not always give you the expected result. The Mintion Beagle V2 is the Swiss Army knife for 3D printing monitoring. It provides real-time video...

MINIWARE ES15: The Screw Neuralyzer

MiniWare ES15 electric screwdriver
The MINIWARE ES15 electronic screwdriver has a cool design that reminds me of the Neuralyzer from the Man in Black movie. It is made from shiny stainless steel, and it has about the size of the epic memory eraser tool from MiB. As an avid...

VIFLY ShortSaver V2: The Smart Smoke Stopper for FPV builders

VIFLY ShortSaver V2
When I connect the battery for the first time to a newly built FPV drone, I wait with bated breath to see if everything is OK and no smoke comes out. Short circuits due to wrong wiring and bad soldering are the most common...

Walksnail Avatar VRX: HDMI digital FPV receiver

Walksnail Avatar VRX
Undoubtedly, one of the most expensive parts of an HD digital system is the FPV goggles, and here comes helping the Walksnail Avatar VRX. Thanks to its HDMI out can be used with your existing analog or digital FPV headset with HDMI in. If...

BetaFPV 450mAh 2S LIPO for Pavo Pico and other CineWhoops

BetaFPV 450mah 2s
Micro CineWhoops, like the Pavo Pico, have gained immense popularity due to their small size, agility, and ability to navigate tight spaces while recording 4K footage. Choosing the right LiPo (Lithium Polymer) battery for your drone is crucial for achieving optimal flight performance and...

MEPS SZ F7 Mini: Small and versatile F722 flight controller

MEPS SZ F7 Mini FC
F722 flight controllers like the MEPS SZ F7 Mini find applications across various FPV drone platforms, from racing and freestyle quadcopters to professional aerial cinematography rigs—the precise flight control, advanced features, scalability, and configurability suit novice pilots and seasoned professionals. The flight controller (FC) is...

Bluetti AC180: The smart power station

Bluetti AC180
The Bluetti AC180 was first announced on 22 March and became available for orders on the 1st of June. We received this power station for review in late June, so we have about a week of testing behind. Many confuse storage capacity with output power....

Hawkeye Thumb: Ultra Light 4K camera for FPV drones

Hawkeye 4K Thumb
At first look, the Hawkeye 4K Thumb camera is an excellent choice for those that find the GoPro too big or expensive but still what to record stabilized UHD videos. Weighting just 15.5 grams, it can be installed on almost any drone size. In...

FlyColor Trinx G5 60A ESC: Fierce, Durable & Speedy

FlyColor Trinx G5 60A ESC
An Electronic Speed Controller, or ESC, is a crucial electronic component in battery-powered devices such as drones, RC cars, and other brushless motor systems. Its primary function is to control the speed and direction of the motor by regulating the supplied power. 4-in-1 drone...

DJI Avata and O3 Air Unit Filter kit from K&F

K&F DJI AVATA and O3 Air Unit Filters
If you want cinematic-like smooth footage with natural motion blur, you must slow down the DJI AVATA or O3 Air Unit shutter speed. In order to do this, you will need a good set of ND filters. By reducing unwanted reflections, a CPL filter...

Amax F5L frame and Performante 2306 motors

Amax F5L frame and Performante 2306 motors
The Amax F5, designed in Germany, is a popular FPV frame aimed for freestyle. This review will look closely at the "L" version, optimized for long-range flights. The Amax F5L can be equipped with both analog and digital FPV systems. It can accommodate 16,...

MiniWare TS101 Soldering Iron for drone projects

MiniWare TS101
When it comes to soldering small electronic components, TS101-like pen-type soldering irons are the most popular. These compact, lightweight welding tools resemble a pen in shape and are designed for small-scale soldering tasks. They generally have fast heat-up times, allowing you to start soldering...

CNHL 4S 2000mAh & 6S 1500mAh: Long-range FPV LIPOs

CNHL 4S 2000mAh and 6S 1500mAh LIPO batteries
For long-range FPV flights, you will need much higher capacity batteries than for freestyling and racing. Commonly, 5" LR FPV drones run on 4S or 6S batteries. You must choose the right battery according to your motor's KV ratings. For example, the CNHL 4S...

Elegoo PLA: Cheap 3D filament for big projects

Elegoo PLA filaments
I mostly printed drone parts in my last filament reviews, so I decided to try something else this time. Using Elegoo PLA filament, I printed a vertical modular hydroponic tower system for plants. My wife was happy to find out that she would always...

Meps 2306 motors and Meps Space 45A ESC

MEPS MINI SZ45A ESC and MEPS 2306 motors
In terms of flight performance, the most important things are the motors and ESC. You can have the best flight controller, but the brain can't fly without muscles. This review will closely examine the Meps SZ2306 motors and Meps MINI SZ45A ESC. If you...

RushFPV Blade F722 V2 digital flight stack

RUSHFPV F722 FC and BLADE 50A ESC
Looking for a versatile and easy-to-use flight controller stack for your next digital FPV drone? Check out the RushFPV F722 V2 + 5A ESC Stack which has just been released and seems a reliable option. The biggest advantage of this flight stack is that...

VIFLY Beacon and Finder V2 drone buzzers

VIFLY Beacon and Finder V2
Vifly makes many useful FPV accessories, and self-powered buzzers are between ones you should keep permanently installed on your drone for safety. In this review, we will have a closer look at the ViFly wireless drone Beacon and ViFly FPV quadcopter Finder V2. Despite...

Walksnail WS-M181 GPS: Fast lock, 6 positioning modes

Walksnail WS-M181 GPS
Walksnail entered the FPV world with its AVATAR HD digital FPV transmission, which wanted to offer an affordable alternative to the existing solution. Now, the company started to provide other accessories for FPV enthusiasts, such as GPS modules, VTX antennas, and more. In this...

Walksnail Avatar HD Pro review

Avatar HD Pro review
Last week, Caddx's sub-brand Walksnail officially released their second generation digital FPV system. Our Avatar HD Pro review covers features, specs, wiring, and low-light performance. A few years ago, DJI introduced the world's first HD digital video transmission system intended for consumer FPV drones. Caddx...

iFlight BLITZ E55 4-IN-1 ESC review

iFlight BLITZ E55 ESC
An ESC (Electronic Speed Controller) is an essential part of an FPV drone that controls the speed of the brushless motor. It is responsible for receiving signals from the drone flight controller and converting them into motor commands by adjusting the amount of power...

CNHL LI-ION 4S 3200mAh: For Long-Range and not-so!

CNHL LI-ION 4S 3200mAh review
Initially, LI-ION battery packs for long-range drones were homemade by hobbyists. They connected 4 or 6 cells serially to achieve the desired voltage. Sony VTC6 18650 batteries were used the most due to their excellent reliability. Panasonic and Samsung LI-ION proved to perform well...

SUNLU PLA Carbon Fiber filament: Is it Good for Drone Frames?

SUNLU PLA-CF
3D-printed FPV drone frames offer a number of advantages over traditional frames made from carbon fiber or other materials. Firstly, they can be completely customized to suit the pilot's specific needs, allowing for greater control over the design process and resulting in a perfectly...

Bluetti EB3A review: Aimed to power your outdoor fun!

Bluetti EB3A review
When camping, road-tripping, or having outdoor activities that involve charging various gear, such as smartphones, cameras, and drones, a small portable solar generator like the Bluetti EB3A is a more convenient solution than a heavy home-backup power station or gas generator. It is quiet,...

eSUN PLA+ review: Grab The Best Filament!

eSUN PLA+ filament review
PLA (Polylactic Acid) is the most popular and widespread filament used in 3D printing. It’s affordable, easy to print, and, more importantly, safe (made from natural materials). PLA is also considered compostable and recyclable. eSUN has a wide range of PLA filaments with different characteristics...

Nanovia filaments review: Best for RaceWhoops

Nanovia filaments
3D printing has become increasingly popular in recent years thanks to its affordability and ability to create complex and elaborated objects in the comfort of your garage. One of the most important decisions you'll make when 3D printing is choosing the suitable filament, as...

Sunlu Terminator 3 (T3) review: Fast but Rusty

Sunlu T3
The Sunlu Terminator 3 (T3) is an ambitious 3D printer that promises five times faster print speed than most of its contenders. Priced for only $199.99, it comes with 250mm/s high-speed printing, a metal double-gear extruder, and a 16 points auto-leveling system. Our review...

eSUN eBox filament dryer review

eSUN eBox filament dryer box
When I got the first 3D printer and had only a few meters of demo filament, I didn't realize the purpose of a filament dryer like the eSUN eBox. Later, when I started to test more and more types and colors of filaments, I...

Anker 757 (SOLIX F1200) review

Anker 757 PowerHouse
I never thought I would need a power station until I reviewed the Anker 757. After a few days of testing, it proved to be a device with multiple applications. From bringing the conform to your home, in the middle of the forest, to...

Elegoo Neptune 3 Plus: Budget large 3D printer

This year Christmas arrived earlier! Yesterday, when I came home, a massive package was waiting for me in the hall. It was the Elegoo Neptune 3 Plus in the biggest box that I ever got a product for review. In November, Elegoo officially announced...

FlyFish-RC Volador VD5 review: Frame kit for O3 Air Unit

FlyFish-RC Volador VD5
Our FlyFish-RC Volador VD5 review covers building instructions, user experience, and flight performance. With the release of the new DJI Air Unit O3, FPV hobbyists started to look for compatible frames. FlyFish-RC has four suitable frames, two 5" (True-X and Dead Cat) and two...

DJI O3 Air Unit review: Cinematic Digital FPV system

DJI O3 Air Unit
I ordered the DJI O3 Air Unit to review it on the first day of its official announcement. I have already tested its predecessors, the original Air Unit and Caddx VistaRunCam Link, and I had big expectations from this new release. In 2019, DJI changed...

SKYSTARS F722HD Pro FC for DJI O3 Air Unit

SKYSTARS F722HD flight controller review
With the release of the new DJI O3 Air Unit, everyone started to look for a compatible flight controller. The SkyStars-RC F722HD Pro has impressive specs and a dedicated digital VTX connector. SkyStars offers the F722 MINI HD Pro in a bundle with three...

Moza AirCross S: The Swiss Army Knife of Gimbals

Moza AirCross S gimbal
Over the past four years, Gudsen Moza has steadily improved upon its professional AirCross gimbal series. The mighty AirCross S continues the trend of being smaller and even more versatile. It can accommodate a wide range of camera devices and even more simultaneously. If you...

ManiaX Power 4S FPV LiPo review

ManiaXPower FPV LiPo
Before we get into details in our ManiaX Power FPV LIPO review, let's talk about some general things you should consider before purchasing a drone battery. When choosing a drone LiPo, the first things to look at are cell count, capacity, and C-rating. Cell count...

DJI Mini 3 PRO filters: All day, for All situations

DJI MINI3 Pro K&F Concept filters
The DJI Mini 3 Pro is a compact and versatile flying camera for content creators. Its 4K camera features 3-axis gimbal stabilization and true vertical (portrait) mode for TikTokers. K&F Concept's filter kit is an excellent addition to this drone when shooting in challenging...

Elegoo Neptune 3 Pro: Goodbye my old 3D printer

Elegoo Neptune 3 Pro
The new Elegoo Neptune 3 Pro 3D printer has some exciting features that make it the dream tool of any drone builder. It allows you to print all the necessary parts in the comfort of your garage. The most significant advantage of the N3...

GoPro HERO9/10/11 filter kit from K&F Concept

K&F Concept GoPro 9/10/11 filters
During my experience with FPV drones, I've learned that filters are crucial when trying to get smooth cinematic footage, but it is important to choose the correct filter and camera settings. Neutral density (ND) and circular polarization (CPL) filters are a must-have in order to...

Happymodel EP1 Dual ELRS Receiver: True Diversity!

Happymodel EP1 Dual ELRS
The Happymodel EP1 is the first ELRS-enabled true diversity radio receiver. It aims to provide the best range even in difficult conditions. Happymodel EP1 has two antennas and two radio modules for doubling the signal quality. In theory, "Diversity" uses at the time only...

SIRUI Traveler 5C: Carbon Fiber Field Tripod

Sirui Traveler 5C
I purchased my first tripod together with my first digital camera, about 20 years ago. It was a cheap unbranded model that served me well for many years. A few years later, I purchased a more versatile tripod from a trustworthy Italian brand when...

ExpressLRS Recovery Dongle (FTDI USB to TTL)

BetaFPV ELRS Recovery Dongle
BetaFPV was among the first drone brands that joined the ExpressLRS team by adopting their high-performance Open Source Radio Control Link. The ELRS Recovery Dongle comes in help for those who brick their radio receiver when failed in updating or flash firmware by using...

Foxeer Foxwhoop 25: From frame kit to flying CineWhoop

Foxeer FoxWhoop25
The Foxwhoop25 is advertised with the 'Unbreakable drone' headline. Foxeer even promises a lifetime warranty for the protection guard. Some dude on YouTube did a car-crushing test. Being strong and slightly flexible at the same time passed the torture. Of course, this does not...

RadioMaster ELRS EP1 & EP2 Nano RX radio receivers

RadioMaster EP1 and EP2 Nano RX
A few months ago, RadioMaster introduced two ExpressLRS-compatible radio receivers with their Zorro transmitter. This review will look more closely at the RadioMaster ELRS EP1 and EP2 Nano RX ELRS radio receivers. ExpressLRS is a relatively new radio protocol that is focused on range and...

ToolKitRc M9 review: The talking drone LIPO charger

ToolKitRC M9
In addition to the lots of inbuilt functionalities, the ToolKitRc M9 features cool voice alerts and a multi-angle colour display. With a size slightly bigger than your smartphone and output power of 600W, it is very portable and powerful. Is the ToolKitRc M9 the...

WALKSNAIL Avatar HD Digital FPV: DJI Air Unit alternative

Avatar HD Digital FPV kit
WALKSNAIL Avatar HD Digital FPV kit consists of VTX (transmitter) and two types of camera sizes. You can opt for 14x14m or 16x16m camera mounting factors. Weighting just, 16grams is currently the lightest digital FPV transmitter. By comparison, the Caddx Vista weights 19grams and...

ZHIYUN CRANE-M2S: Must-have gimbal for vlogging and travel

Zhiyun Crane M2S
ZHIYUN's latest all-around vlogging gimbal, the CRANE-M2S is positioned between the Crane-M2 and the Crane-M3. The M2S has a great balance between camera compatibility, features, and price. High-end smartphones like the iPhone 13 Pro Max comes with built-in image stabilization (OIS) that promises close...

Elegoo Saturn S: Large 3D prints at friendly price

Elegoo Saturn S
The Saturn S is the newest member of the 4K resin 3D printer series released by Elegoo and it is an improved version of the original Saturn. The screen is now increased from 8.9" to 9.1" and the print height from 200mm to 210mm....

ND Filters for Autel EVO Nano by FORFOCUS

ForFocus Autel EVO Nano ND filters
If you’re anything like most new Autel Nano owners, you’re likely already searching for compatible accessories such as chargers, cases, spare batteries, or ND filters. In this review, we will have a closer look at the ForFocus Autel Nano filter kit. Neutral-Density (ND) filters are...

Drone landing pad review (Universal & LED from CYNOVA)

CYNOVA landing pads
Eight years ago, when I started this hobby, the first drone accessory that I purchased was a landing pad. Drone aprons give you a safe take-off and landing every time, regardless of the terrain you fly. For example, sand is even more dangerous than...

Caddx Air Unit Micro review: Better than DJI?

Caddx Air Unit Micro
About four months ago, I purchased a Caddx Air Unit Micro kit with the intention to review it. Usually, when I get a new product on my test bench it takes no more than two weeks to publish my evaluation. In the case of...

Best GoPro 10 accessories from PGYTech

PGYTech GoPro 10 accessories
GoPro's latest Hero 10 is a superb action camera, but to get the best footage, you'll need the right GoPro accessories. Many of the best PGYTech GoPro 10 accessories listed here will work not just with all models of GoPro cameras, but also with...

FreeWell Autel EVO Nano ND filter kit review

If you are serious about getting the greatest photo and video results from your Autel EVO Nano drone, you should invest in Neutral Density (ND) filters. In this review, we will have a closer look at FreeWell's 'All Day' kit which includes 6 filters...

GoPro Hero 10 accessories bundle review (HSU 72 in 1 kit + extras)

HSU GoPro10 accessories kit
After I published my GoPro Hero 10 review, I started looking for some compatible accessories. HSU had the most comprehensive bundle that includes 72 pieces of GoPro 10 accessories. Practically, contains everything you could ever need for this action camera, from plenty of mounting...

PGYTECH OneGO shoulder drone bag

PGYTech OneGO
Most drone manufacturers, including DJI, Autel, FIMI, and Hubsan, offer their drones in two package options. Only the 'Premium/Fly More Combo' edition includes a dedicated bag/case. The PGYTECH OneGO looks to be a great storage and transportation solution for those purchasing the more affordable...

Kovol Sprint 120W 4-Port USB PD GaN charger review

Kovol Sprint 120W USB PD GaN charger
Nowadays, most drones weighing less than 250 grams are charged via USB. Laptop manufacturers are also moved from dedicated power adaptors to more convenient PD USB chargers. Often, I have to charge 3-4 devices at the same time and I borrow my wife's and...

RadioMaster Zorro review – Conquer the Sky!

RadioMaster Zorro
From my point of view, the selling point of the RadioMaster Zorro transmitter is its big screen. When you are over 40 years old, you are losing the focusing ability for near vision and due to that, the lens inside your eye becomes less...

GoPro Hero 10 Review (Not Sponsored!)

GoPro Hero 10
GoPro is the action camera industry leader and the Hero 10 Black is the company's new flagship for 2022. I’ve spent more than two months with this camera in order to find out if the on-page specs and features translate to real-world usage. My...

BETAFPV LiteRadio 3 review: New Year, New transmitter

BetaFPV LiteRadio 3 review
BetaFPV's third-generation radio transmitter, the LiteRadio 3, comes with a few cool upgrades, including new nano gimbals, neck strap hook, extended working time, and updated shoulder switches. In addition to the inbuilt TX module (ELRS or FrSky) now has an external Nano TX bay...

MagiMask review: FPV goggles for Phone drones

MagiMASK review
MagiMask is a wearable VR headset that essentially magnifies your existing smartphone screen and allows pilots to view live drone video footage comfortably without being disturbed by sunlight. It is compatible with most popular drone brands, including DJI, Autel, FIMI, Hubsan, and others. Of...

MOZA AirCross 3 review: The Convertible 4 in 1 Gimbal

MOZA AirCross 3 gimbal
The MOZA AirCross 3 is a convertible 3-axis gimbal designed specifically for professional video-makers using mirrorless and DSLR cameras. Supporting a 3.2kg/7.05lb max payload, it can accommodate a wide range of camera bodies. We had a chance to check the AirCross 3 shortly after...

ZHIYUN Crane M3 review: All-rounder vlogging gimbal

ZHIYUN CRANE M3
When I read for the first time about the ZHIYUN Crane M3, I decided that this is the gimbal I need. In the last two years, I reviewed about 10 gimbals but none completely fulfilled my needs. For vlogging, you need a stabilizer that...

Foxeer Apollo Digital camera for DJI HD Digital FPV

Foxeer Apollo camera
Foxeer is the third brand that started manufacturing DJI HD digital FPV system compatible cameras. The Foxeer Apollo works with both Caddx Vista and DJI Air Unit VTXs and it is available with two lens options, 'Standard' and 'StarLight' for night flights. For those...

MINI V8 camera: DJI Action 2 alternative? Hell NO!

Tisi MINI 4k Viran camera
The Tisi MINI V8 is a DJI Action 2 size 4K action camera with impressive specifications that weighs less than 60 grams. Its small size attracted my attention because it is easy to install on FPV drones. As the only review found on this...

BetaFPV 1506 3000KV motor review: Perfect for CineWhoops

BetaFPV 1506 3000KV motors
A few months ago, I tested the BetaFPV Pavo 30, a very capable CineWhoop. Unfortunately, I needed to replace the flight controller and two of the motors due to an accident. While the stock motors were 3400KV, I found as a replacement only these...

MOZA Mini MX2 review: Gimbal with auto phone load

Moza MINI MX2 review
Over the last few years, Gudsen MOZA has steadily improved its smartphone gimbals. The second-generation Mini MX2 continues the trend. It is the first stabilizer with a smart auto-sense phone holder and instant portrait/landscape transition. In a short time, Gudsen Technology became one of the...

Zino Mini Pro spare parts and accessories

Hubsan Zino Mini Pro Spare Parts Accessories
Shortly after I published my Zino Mini Pro review, I crash it. Now, the drone is on my workbench with one broken arm, damaged gimbal support, and cracked bottom shell. The battery in the drone was also damaged, despite that, it fell from about...

Artillery Hornet 3D printer review

Artillery Hornet 3D printer
These days, 3D printers are used in various applications, from education and prototyping to advanced things like bioprinting organs. In the drone hobby, many DIY enthusiasts started to print their spare parts and accessories for long time ago. Lately, Free Zillion, founder of RaceWhoop...

SEQURE SQ-001 review: Soldering Iron for drone repairs

SEQURE SQ-001
The SEQURE SQ-001 is one of the most portable soldering iron at the moment. Its small size and battery-operated mode make it perfect for FPV pilots that like to repair their drones right on the flight field. In our SQ-001 review, we’ll take an...

LDARC EX8 review: FrSky transmitter for cheap

LDARC EX8 review
Last month, LDARC, formally known as Kingkong, announced their third beginner-oriented drone transmitter named EX8. Being compatible only with Futaba & FrSky receivers, without any future upgrade capability, I think they joined late to the game, as everyone moves to ExpressLRS these days. My...

HGLRC Herme ExpressLRS: ELRS TX/RX (900MHz/2.4GHz)

HGLRC Herme ExpressLRS TX and RX
After Happymodel and BetaFPV, HGLRC also announced their first ExpressLRS enabled radio system. Like its contenders, the Herme ExpressLRS also has 900Mhz and 2.4GHz versions. ExpressLRS (ELRS) is an open-source RC link for various applications, including drone communications. ELRS uses LoRa modulation with strong...