Lumenier AXII HD 2 Patch Visor for DJI FPV Goggles
Lumenier AXII HD 2 Patch Visor is a 5.8Ghz antenna system specially designed for DJI FPV Goggles. In addition to the improved range, it customizes your look by choosing the color that matches your style. You can blend in with the sleek Smoke Gray color or stand out with bright colors like Blue, Orange, Green, or White.
In a nutshell,...
Insta360 GO 2 ultra-light camera for FPV drones
The FPV community has been waiting for a long time for insta360 to come up with an improved version of their smallest camera. Due to the rugged design, the new Insta360 GO 2 is a bit heavier compared to its predecessor (26.5g vs 18.3g). Furthermore, it's waterproof up to 4 meters (13ft). Before you become too enthusiastic, without 4K...
AKK X2 review: Super mini VTX with up to 800mW
Since the first FPV drones, VTXs evolved a lot. They became smaller and more powerful. In addition to the compact size and up to 800mW broadcast power, the AKK X2 comes with Smart Audio. This means that you can configure the AKK X2 remotely via your transmitter.
Currently, there are two approaches supported by BetaFlight OSD to control the VTX,...
DJI Osmo Pocket 3 launch date confirmed: 25 October 2023
The Pocket 3 is drone-maker DJI’s upcoming pocket-stabilized 4K vlogging camera and comes with a rotative large screen for vertical and horizontal shooting modes. The third generation has also a bigger 1-inch CMOS sensor for improved low-light performance. By comparison, the original Osmo Pocket (v1) had a 1/2.3" and the second-generation OP (v2) 1/1.7" one.
Quadro_News (Igor Bogdanov) via Twitter/X...
RadioMaster RP3 ExpressLRS 2.4G Nano Diversity RX
For Christmas 2022, RadioMaster announced another 2.4 GHz ELRS radio receiver for long-range enthusiasts. RadioMaster RP3 features a dual-antenna diversity system that ensures a stable signal. You can opt to install one antenna in the front and the second one in the rear of the aircraft. You can also mix polarization by installing one antenna vertically and the other...
HOBBYMATE D6 Elite review: More than a drone charger
In the past, chargers were very basic electronic devices. I remember that ones I tried to repair one and I found inside only a couple of resistors and diodes. Compared to those old charges, the HobbyMate D6 Elite is a very versatile hi-tech gear. In addition to the fact that allows charging almost any type of rechargeable batteries (multi-chemistry),...
Walksnail Avatar HD Goggles X: Future proof modular design
Without any doubt, the FPV headset is the most expensive part of an FPV system, and you would probably like to use your investment for many years. CaddxFPV's new Walksnail Avatar HD Goggles X comes with a modular design that allows upgrading the VTX module and the antennas. The manufacturer promises the release of a next-generation receiving module that...
RADIOMASTER RM 4IN1 TX Module for RC
The RadioMaster 4IN1 external module is a multi-protocol TX that integrates CC2500, NRF24L01, A7105 and CYRF6936 RF chips. It is compatible with more than 70 RF protocols, including DSMX, Flysky, SFHSS, HiTec, HoTT, OMP, Radiolink, Frsky and others. Designed for OpenTX and EdgeTX systems, the RM 4IN1 TX module allows the radio to connect with most mainstream protocols on...
Zino Mini Pro spare parts and accessories
Shortly after I published my Zino Mini Pro review, I crash it. Now, the drone is on my workbench with one broken arm, damaged gimbal support, and cracked bottom shell. The battery in the drone was also damaged, despite that, it fell from about only 4 meters on soft ground. In my opinion, it was a hardware failure but...
DJI Phantom 3 case by Realacc
After you pay about $ 1000 for a quadcopter, you will want to carry and store your precious toy in the safest possible way. In my opinion, a hard case like this Realacc is the best solution for transporting your Phantom 3 quadcopter when you are traveling by car.
Until now, I stored my Phantom 3 Advanced in its original...
Elegoo Neptune 4 series comparison: Pro, Plus, & Max
In May 2023, Elegoo announced its first high-speed 3D printer with Klipper firmware, named Neptune 4 Pro. After four months, they announced two new members of the N4 series named Plus and Max. The Neptune 4 Plus and Neptune 4 Max not only inherit the great features of the original Neptune 4 Pro but also get some significant improvements...